MicroBio MB2 Bioaerosol Sampler

Bioaerosol samplers are vital equipment for us in bioaerosol research, clean rooms, pharmaceutical validation and throughout hospitals wherever air hygiene is vital. The MicroBio MB2 Bioaerosol Sampler has a host of features making it ideal for use in such applications. It has been fully validated and thousands of units are in use worldwide.
 

Now with Sequential Sampling and multi-lingual menu system.

The MicroBio MB2 bioaerosol sampler is capable of using both standard 90 mm Petri dishes or 55 mm contact plates with 220 and 400 hole sampling head option, avoiding the expense of proprietary sampling media. Using standard readily available consumables at low cost with a variety of media makes the MicroBio MB2 an economical instrument to use. The MicroBio MB2 bioaerosol sampler is an invaluable device designed for use in hospitals, with IAQ consultants and validating clean rooms to ISO 14698 requirements and USP797 Guidelines in the United States.

Supplied with the MB2 Bioaerosol Sampler

  • Petri dish and contact plate spring sets

  • 220 hole x 1 mm stainless steel or 400 x 0.7 mm anodised aluminium sampling head

  • Printed operating manual

  • Padded carry bag

  • Mini table-top tripod

  • Multi-voltage world-wide charger with UK, Euro, USA, Australia and 12V in-car plugs and
    pre-charged cells so the MB2 is ready to use out of the box

  • Certificate of Calibration
     

Downloads

MicroBio MB2 Manual (June 2015 onwards)

MicroBio Manual (Pre-May 2015)

Positive Hole Correction Analysis Spreadsheet using Excel™ (Windows™ or Libre Office)

Positive Hole Correction Analysis Spreadsheet using Numbers™ (Apple Mac).

MicroBio MB2 IQ/OQ/PQ Document Template

Sampling Head Option

The MicroBio MB2 can be purchased with the option of one of two types of sampling heads.  The MicroBio MB2 will be calibrated for use with the selected head.  If swapping to another head type, the MicroBio MB2 must be re-calibrated.


220 x 1 mm hole stainless steel head

This is the standard head sold with the MicroBio MB2 and MB1 air samplers.  It is designed as a dual purpose head for both 55/60mm contact plates or up to 90mm Petri dishes.  The d50 cut-off point os 1.7 um and has a jet velocity of 9.63 m/s.  It is the ideal head for general purpose sampling in air quality and food production.

 

 

 

 

 

 

 

                               MicroBio 220 Hole Sampling Head

400 x 0.7 mm hole anodised aluminium head

Available as a no-cost option, this head provides full coverage of 90mm Petri dishes with a d50 point of 1.35 um and air jet velocity of 10.7 m/s.  These heads are ideal for use in areas needed higher sensitivity of collection.

 

 

 

 

 

 

 

 

                             MicroBio 400 Hole Sampling Head

 

Tripod  (Part No. P0001TRI001)  –  NOW INCLUDED AS STANDARD!

Aluminium indoor table-top tripod for use with MicroBio MB2. This tripod enables the MB2 to stand on its own with a height range of 145 to 245 mm (to base of MB2).

 

                                           MicroBio Mini Tripod

 

Head Retaining Spring  (Part No. P0001M009)

Replacement sampling head retaining spring.  Sold individually

 

 

 

 

 

                                             Head Retaining Spring

 

Contact Plate Holding Springs
(Part No. P0001M007)

Replacement springs used to hold 55 mm contact plates.
Sold in a pack of 3.

 

 

 

 

                                        Contact Plate Springs

 

Petri Dish Retaining Springs  (Part No. P0001M008)

Replacement springs used to hold 90 mm Petri dish plates.
Sold in a pack of 3.

 

 

 

 

                                   MicroBio Petri Dish Springs

 

Spring Retaining Screws  (Part No. P0001SCR003)

Replacement stainless steel M3 x 6 screws used to fasten the dish, plate and head retaining springs.  Sold in a pack of 10.

 

 

 

 

                                  MicroBio Head Screws